How to fix glass splashbacks

Made of toughened glass, our kitchen glass splashback panels are specifically designed to work behind a kitchen hob above the worktop. They provide an instant transformation in a matter of minutes with an easy fix DIY solution. In this how to guide we talk you through how to fix your new glass splashback panel to the wall to update your kitchen.

The glass splashbacks are manufactured in large sheets which are then cut, polished and toughed. All our glass splashbacks are toughed to British Standards (BS EN 12150) meaning it’s 5 times stronger, with a higher thermal strength, when compared to annealed glass. This makes it the perfect touch to add behind your kitchen’s hob.

The 60x75cm glass panel is available in a range of designs to suit your kitchen’s aesthetic. There are 3 plain colours: black, olive and white which offer a muted block of colour. There are 3 metallic shades: pewter, copper and gold which add a subtle shimmer as the light hits the panel. The grey mirrored design is great for smaller kitchens with less natural light available. Finally, there are 2 fluted designs in charcoal and white that add a touch of opulence and tactility to the space.

All have a smooth finish for easy cleaning and are made from 30% recycled materials.

When you first receive the splashback, inspect the panel carefully to ensure there are no visible scratches through the protective film.

You’ll need to acclimatise the glass splashback before installation to allow its adhesive tape to warm up to +10°C (applying the tape in colder temperatures could affect its bonding).

You’re not able to apply the glass splashback directly onto tiles so if you have an older splashback that you’re looking to replace then you will need to remove this and the old adhesive before you affix the new splashback.

Finally, you’ll need to ensure that the splashback is installed at least 100mm away from the hob flames, ensuring no direct contact or close proximity to the flame as this could damage the colour coating and glass.

The splashback comes with adhesive tape on the back however, this isn’t enough to fix it permanently into place therefore, when fixing your glass splashback, we recommend using the Soudal Silirub 2 Neutral Cure Silicone. Not only is this a high-quality fixing product, but it also won’t react to the paint on the back of the glass and won’t change colour as it cures.

You will need:

- Soudal silicone cartridge and gun

- Masking tape

- Kitchen silicone sealant

- Timber baton (if not applying the splashback directly on top of a work top)

- Spirit level

- Measuring tape

You’ll need to ensure the kitchen wall is smooth, clean and free from any cracked plaster, grease, large holes etc.

You can sandpaper to smooth down the wall and patch up any holes with filler. Once re-sanded, cleaned and dry you can begin fixing your splashback.

The next step is to measure the placement of your splashback. Carefully mark the centre point of where the splashback should sit.

Due to thermal expansion your glass panel will naturally expand and contract so it’s important to keep a 2mm expansion gap around the perimeter of the panel, so factor this in when measuring.

At this point, place it on the wall with help from someone so you can see it in situ and ensure it looks how you want it to. Once happy you can begin fixing.

If it’s sitting on top of a worktop, apply a thin line of sealant along the back of the back worktop where it meets the wall to seal and gaps. If the panel isn’t supported by a worktop, then you’ll need to pin a timber baton to the wall to prop it in place whilst the adhesive cures.

Apply the Soudal Silirub 2 silicone to the rear of the glass in between the strips of adhesive. Remove the paper backing on the top and then carefully place the glass into position.

Use masking tape to secure the splashback whilst the adhesive cures, this can take up to 24 hours. Once it’s fully cured you can remove the tape.

The final step is to apply a thin bead of kitchen silicone sealant in the desired colour along all the exposed edges. This will stop water and grime getting behind the panel as well as providing a neat finish.

Maintaining the look of your glass splashback is easy, it needs a regular clean to prevent surface build up of dirt and grime, we’d recommend using the Fila Multi-surface cleaner.

You should never use an abrasive cleaner or material on the glass as it will damage it, with this in mind we’d recommend wiping it down every time you’ve used the hob to avoid any dirt drying on the surface making it harder to remove.